DIY Pool Deck

Total
0
Shares
diy pool

We recently published an article about above ground pools, and we received numerous requests to write an article about how to build a DIY pool deck around an above ground pool, so here it is. Above ground pools are great and inexpensive, but if you want to take your pool experience to the next level, you’ll need a place to sunbathe and relax next to the pool. Most people believe that building a DIY pool deck is too difficult for them, but it isn’t. Experienced workers who have built several pools using DIY guides can even start and promote courses on how to build custom above ground pools.

We recently published an article about above ground pools, and we received numerous requests to write an article about how to build a DIY pool deck around an above ground pool, so here it is. Above ground pools are great and inexpensive, but if you want to take your pool experience to the next level, you’ll need a place to sunbathe and relax next to the pool. Most people believe that building a DIY pool deck is too difficult for them, but it isn’t. Experienced workers who have built several pools using DIY guides can even start and promote courses on how to build custom above ground pools.

1. Digging up holes and setting up posts

Digging holes and mounting posts for pool deck

The first thing in any DIY pool deck project is clearing the ground where your future deck will be. Strip all the grass and around 2 inches of dirt where your construction site will be. For the posts we used 4 x 4 lumber and we advise you not to use smaller lumber than that. First take four boards and setup the future look of your deck on the ground. Use that to mark the spots for the posts and remove the boards. Use a post hole digger to dig up holes slightly bigger than the posts. Make sure that your holes are deep enough and that they are below the frost line, at least 3.5 ft. Set the posts in the holes, level them and start to fill the holes with rocks. Once you’re half way there use four larger rocks and secure the post on each side. Then fill up the rest of the hole with rocks. You can also use concrete but this method will be solid also. Don’t forget to protect the part of the post which goes into the ground with waterproof wood sealant because otherwise the posts will rot in the ground.

2. Making the frame of DIY pool deck

After all the posts are in place it’s time to start with the frame. For the beams and joists we used 2 x 6 boards and we advise you to not to used smaller lumber than that. Before you start with the frame, take four pieces of 2 x 4 and use them to temporary secure and level the corner posts. After you screw in the beams you don’t need them anymore and you can remove them. Your beams need to be perfectly leveled and it’s hard to achieve that if both ends of the beam are loose. Use a small piece of wood and temporary screw it to the post below the selected height of the beam and place one end of the beam on it. That way you’re aligning only one end of the beam and you’ll see it’s much easier to level the beam this way. The three outside beams must be the same height and the one near the pool will be 6 inches below. The main frame is now done and you can now secure all the posts and put weed barrier and stone below your future deck. We advise you to do that now because after the deck is finished it’s hard to crawl under it.

Building a frame for pool deck

3. Making the stairs and securing posts

It’s time to construct the staircase for your deck. For that you’ll need two pieces of 2 x 12 for stringers, 7 pieces of 2 x 6 for risers, 6 pieces of 2 x 8 for runners, one piece of 2 x 6 for the top runner and two pieces of 4 x 4 for the stair posts. Make 6 inch rise and 8 inch run on both stringers and mount them on the beam with stair stringer brackets. Separate the stringers depending on the size you want your stairs to be. Dig up two smaller holes and put 4 x 4 at the end of both stringers and secure them to the stringers.

Before you start with the joists we advise you to temporary secure the upper ends of the posts with 2 x 6 boards. This will reinforce the structure and prevent it from moving while installing joists. After you install the joists you can remove them because the structure is secured with joists now.

Stairs for DIY pool deck

4. Installing joists and trimming the posts

Joists are used as a base for the flooring and you need to do that part with extra care if you want to have a nice and leveled deck. For the joists we used 2 x 6 boards and we secured them additionally with corner brackets. You have to measure the length for each joist because the shape of the pool determines the length of the joist. When you measure the distance, take away 2 inches because you will insert boards between the joists and the pool and connect them with joists. You need to put one joist at least every 20 inches if you want a sturdy decking. We installed one joist on each side of every post for additional security and also we installed blocking between the joists to prevent them from twisting. Also we secured the joist on each corner with corner brackets.

You probably noticed that the posts aren’t the same height and that they are probably to high. You need to decide how high your railing will be and mark the height on one post. The use a 2 x 4 and a level to transfer that height on other posts. Trim all the posts on the same height and use the 2 x 4 for the top and bottom rail. If you want, you can add aluminum railing for extra touch.

Joists and railings for pool deck

5. Decking and railings

Your DIY pool deck project is coming to a final stage, it’s time for decking. For decking you can use 5/4 x 6, 5/4 x 8 or 5/4 x 10 boards. We used 5/4 x 6 decking boards because it looks better. First use 1 x 4 boards and secure them around the pool edge, closing the gap with the pool completely. Then start to lay 5/4 x 6 boards from the far end and work your way to the pool. When you come to the 1 x 4 boards it will be a little tricky to cut the perfect shape to match the gap. The trick is to put the board on top of the 1 x 4 board and align it to the last 5/4 x 6 board. Then crawl under the deck and mark the gap with a pen and then cut the board. Decking is really a simple process, just make sure that you secure each board with each joist with wood screws. And always first drill a hole slightly smaller than the screw to avoid cracking and splitting. After you complete the decking finish the stairs by installing the risers and runners.

The final thing left to do is railing.  It’s really a decorative final touch and you can complete this part in the way you prefer. We mounted the 1 x 2 spindles every 6 inches and 1 x 4 boards on top of the railing.

Decking for DIY pool deck

DIY other budget-friendly backyard ideas, put some deck chairs and sunshade and enjoy a cold drink by the pool on your new DIY pool deck. Including a glass deck railing will add an aesthetic and elegant look to your exterior house. If you want, you can add aluminum railing for extra touch. The cost of materials is increasing, but you can use online loan options to cover those costs. Title cash from title loans is the perfect way to cover material costs like wood and metals.

Leave a Reply

Your email address will not be published. Required fields are marked *

You May Also Like